Unit 2, Knockmitten Industrial Park, Knockmitten Lane, Naas Road Dublin 12, Ireland

Monday: 10.30am – 2.00pm
Tuesday: 10.30am – 2.00pm
Wednesday: 10.30am – 2.00pm
Thursday: 10.30am – 2.00pm
Friday: 10.30am – 2.00pm

Frequently Asked Questions

Please read our FAQ before sending us a message.

No our columns cannot support weight; they are for decoration purposes only. You may enhance structural supports such as steel or concrete by wrapping the half columns around this.

Another idea used for columns is to fill them with sand or cement. This is possible by following the simple instructions below:

Around each column, construct a shuttering or strapping prior to pouring in the mixture.
There must be a hole made in the bottom. The column must be upside filled upside down and must remain like this whilst the mixture dries. Filling must be done in several stages to prevent the column bursting.
The shuttering has to stay around the column until the mixture has completely set.

Most of the more decorative covings, panels mouldings and some skirting boards are available in flexible. We do not carry flexible products in stock but these can be ordered and the lead time is approximately 3-4 weeks.

For more information on flexible products please contact us on sales@covingdirect.ie or telephone:

For a guide to fitting flexible mouldings please see our FITTING GUIDE

Coving or mouldings within the home are regarded as decorative rather than part of the building structure and therefore are not subjected to the normal fire regulations.
If a fire does breakout within the home, the mouldings will melt but will not add to the fire.

For commercial buildings or if there is a chance that Orac will come into contact with an open flame or temperatures above 350 Celsius we recommend that a flame retardant paint be applied.

All Orac products come pre primed for you, therefore this removes one job for you and makes installation easier. We recommend that you give each length a slight sanding and clean to remove and dust or dirt on the surface. This will allow the paint to grip better o the primer and give you a better paint finish.

Acrylic paints are the best to use as they have some elasticity in them and this will be a benefit is there is any movement between the coving and wall or ceiling.
Emulsion paints can be used but if the movement between the coving and wall or ceiling occur, small cracks in the paint may be visible.

If installing Orac externally please note that as well as using Decofix Hydro you must also use and exterior grade paint that can cope with all weather conditions.

For Covings, Panels mouldings and Skirting boards we recommend that you use FDP500 Decofix Pro. It is a slow drying Extra Strong glue that ensures a long lasting seal between the moulding and wall or ceiling. It can be painted after it hardens (normally takes 24 hours). It can also be used as a water based filler for between the joints.

We sell it in 310ml tubes, we recommend that for 1 tube will do 2.5 lengths of 2.4 metre Orac. For 2 metre lengths this tube will do 3 full lengths.

FX200 Decofix Extra is a glue for seam joints between the mouldings. FDP500 can be used around the joints but this will create stronger bond between the two lengths.

FDP700 is Decofix Hydro and is used when Orac products are put outside or in humid areas such as damp rooms.

If you require any more advice on the particular adhesives available please contact us onsales@decorativecovingsolutions.ie or on telephone

You will need a mitre box to cut the angles for the corner. Mitre boxes can be purchased in our accessories section. Mainly the FB13mitre box can be used but some larger cornices may require a bigger mitre box.

Before cutting please see our FITTING INSTUCTIONS, this will give you a step by step guide to cutting a corner.

Please note, always start with an external corner as it is more noticeable and work towards the internal corner.

When cutting please use care and though and there should be no reason why a perfect mitred corner cannot be achieved.

A medium tooth standard saw that can be bought in any DIY/ Hardware saw is all that is required. The only other tool you will need when cutting is a mitre box, remember that the mitre box must have a sufficiently high back plate that is appropriate to the coving/cornice that you will be cutting. Orac produce mitre boxes and these can be purchased under the accessories.

There are pre mitred corner pieces available for a few of the more popular mouldings such as CX100,CX101,CX106,CX107,CX123,CX109. There are both internal and external corner pieces available for these.

If it is not specified on the order page that there is a corner piece then unfortunately you have to mitre the internal and external corner pieces.

For tips on how to mitre corners please see FITTING INSTRUCTIONS

There are selected panels mouldings which also have corner pieces this will be specified on the order page, if you require any further information on corners, please e-mail us on sales@decorativecovingsolutions.ie

PLASTER MOULDINGS ORAC POLYURETHANE MOULDING
HEAVY TO INSTALL: LIGHT TO INSTALL:
Cannot be used on lowered ceilings as it is too heavy.
Takes at least two men to do the job and lift the mouldings.
Can be installed on any type of ceiling.
Can lower the structural weight in bigger buildings.
Can lower the structural weight in bigger buildings.
One man can install this one his own, saving fitting/labour costs.
TIME CONSUMING: TIME SAVING:
A heavy difficult job which takes a lot of time Easy job which goes up a lot faster (up to 4 times faster than plaster).
When time is a problem, Orac is the perfect solution.
DIRTY JOB: CLEAN JOB:
A lot of water and dust. Difficult to use for refurbishment jobs due to this Only glue is used, therefore no mess, perfect for new builds and renovations
DESIGN NOT VERY DETAILED: VERY DETAILED DESIGN:
Each length does not have the same detail, as each length is made in a mould, once it starts to wear and reach the end of its life, the design begins to fade. Each length has its detail put on by a machine, therefore it means that the design on each length is more uniform than with plaster moulding.
VERY FRAGILE DURABLE:
Each length can be easily transported around as it is very durable and cannot be easily damaged.
OPEN JOINTS NO OPEN JOINTS
Orac fix extra is used to fill any joints and give a smooth finish
NOT USABLE IN HUMID AREAS CAN BE USED IN HUMID AREAS:
As long as used with special glue DECOFIX HYDRO
NO PRIMER COAT ON THE MOULDINGS ALREADY PRE PRIMED LENGTHS
DIFFICULT TO PAINT EASY TO PAINT
DOES NOT TAKE ALL KINDS OF PAINTS TAKES ALL KIND OF PAINT
Plaster moulding will absorb the paint, therefore it takes more coats to cover it properly. As each length is pre primed it is easier to paint and does not absorb the paint so less paint used.
Any paint or effect can be done on the lengths.
Smooth surface so easier to pant.
DIFFICULT FOR CURVES FLEXIBILE RANGE AVAILABLE FOR CURVES:
Orac Flex solves this problem with regards to installation and time

Send us an email

Full Name *

Email Address *

Subject *

Your Message *